色狠狠色狠狠综合天天-色狠狠狠色噜噜噜综合网-色狠狠狠狠综合影视-色狠狠干-色狠狠成人综合网-色狠狠成人综合色

<big id="m0aay"></big>

熱門圖片

當前位置：首頁 >> 臺灣研儀編程器 >>

LabTool-T400

發布時間：2018/5/30 閱讀：10936次

AEC Programmer LABTOOL-T100

LabTool-T400 Option 100

The LabTool-T400 Option 100 is a shirk version of LabTool-T400 with affordable price.
The Option 100 remove three set of pin driver on T400 only one set pin driver left on T400 , The LabTool-T400 Option 100 is idea solution to customer in R/D who need to program very high density Flash chip with low voltage such as 3.3V , 1.8V and 1.2V. those high density and low voltage do not support by Labtool-48UXP.
LabTool-T400 option 100 can be upgrade to full function LabTool-T400 later on by purchase extra three set of pin driver and filed install by customer.

Support 3.3V to 1.2V flash memory chip in VCC and I/O without low voltage converter.
Flash chip support up to 128G bit.
Extremely high speed: it blank check a 64M bit flash chip in 1.6 seconds, program the STM28W640CT (4 word programming algorithm) within 11.5 seconds, verify within 3.2 seconds.
USB interface: support USB 1.1 or 2.0
One PC can connect up to 16 unit Labtool-T400 to perform Asynchronous programming
Device insertion /continuity check before programming.
Target quantity and Max failure rate alarm.
Supports Windows 98SE / ME / 2000 / XP / Vista(32bit) / 7 / 8.1 / 10
1 year warranty

LabTool-T400 Turbo Flash Gang Programmer is four sockets PC-based Gang Programmer. It features four independent isolated modules, extremely high speed in writing flash memory chip. It supports 3.3V, 2.7V, 1.8V and 1.2V chip in both VCC and I/O without low voltage converter and handles 8/16/32 bit flash chip in different package through adapter modules, up to 128Gb flash can be support. The LabTool-T400 is an ideal programmer for customers in GSM, 3G Mobile, PDA, Internet router and others.

The LabTool-T400 has build in Compact Flash Card (CF) on board that reduce the massive data transfer between the PC and LabTool-T400 .The LabTool-T400 performance reach the speed limitation of the chips in its spec. No other gang programmer today and future can beat the speed of the LabTool-T400.

The LabTool-T400 use the 90nm FPGA chip in hardware design, it can handle the chip from 3.3V to 1.2V in both VCC and I/O without need special low voltage converter circuit. This new technology fulfils customer's need and makes customer's investment fully protected.

The LabTool-T400 has reserved the growth potential in chip's density. It covers 8/16 bit flash today and future's 32 bit flash chip. Its I/O pin driver can cover flash with Max 128G bit in density. This growth potential protected customer's investment without purchasing a new generation programmer over a decade in future.

The LabTool-T400 interface with PC through USB interface, which support USB 1.1 and 2.0. If customer needs more units in production, just purchase extra LabTool-T400 and connect those LabTool-T400 through USB Hub, up to 256 LabTool-T400 can be attached to one PC. Recommend with 8-16 unit LabTool-T400 control by one PC to avoid performance decrease. Such configuration has significantly reduces the cost per station with low initial purchase cost and growth potential in future.

The LabTool-T400 adapter module has independent ID. After inserting the module in the LabTool-T400, the system will detect the module's ID and compare the corresponding adapter modules with the chip select in software. This future prevents the wrong adapter module insert or wrong chip selection in operation.

Flash memory: include NOR , NAND, EEPROM and other flash technology
Device data width: 8, 16 and 32 bit
Max flash density support: 512Mb with 128M byte Compact Flash Card install on board (standard offer), can be extend to 128Gb with exchange higher density Compact Flash Card on system hardware.